Leave Your Message
PV-PE Series: Photovoltaic Panel Edge Seals
RUBBER EXTRUSION

PV-PE Series: Photovoltaic Panel Edge Seals

A critical sealing component for PV panels, designed to protect edges from moisture, dust and external damage, enhancing panel durability.

    manufacturing-standards

    Factory Real Photos

    密封条

    Product Specifications

    Model No.

    Overall Width

    Height

    Insert-in Width

    Applicable PV-Module Gap

    Material Option

    PV-PE-001

    43 mm

    34 mm

    27.5 mm

    18-22 mm frame gap

    EPDM / PVC

    PV-PE-002

    28 mm

    31 mm

    9 mm

    12-16 mm frame gap

    EPDM / PVC

    PV-PE-003

    35-49 mm

    29 mm

    17 mm

    20-26 mm frame gap

    EPDM / PVC

    PV-PE-004

    35 mm

    32 mm

    19 mm

    14-18 mm frame gap

    EPDM / PVC

    PV-PE-005

    37 mm

    37 mm

    23 mm

    22-28 mm frame gap

    EPDM / PVC

    PV-PE-006

    37 mm

    37 mm

    23 mm

    22-28 mm frame gap

    EPDM / PVC

    光伏板
    光伏

    Product Features

    ● Made of weather-resistant EPDM/PVC; excellent UV & aging resistance Flexible, fits various panel edge sizes; good adhesion to frames

    Material Properties

    1)EPDM (Premium Grade, recommended for PV system)

    Item

    Test Result

    Test Standard

    Hardness

    55-65 Shore A

    ISO 868

    Tensile Strength

    ≥7.0 MPa

    ISO 37

    Elongation at Break

    ≥300 %

    ISO 37

    Compression Set (70 ℃×24 h)

    ≤25 %

    ISO 815-1

    Operating Temperature

    -40 ℃ ~ +120 ℃

    —

    Water Absorption

    <3 %

    ISO 62

    1)EPDM (Premium Grade, recommended for PV system)

    Item

    Test Result

    Test Standard

    Hardness

    60-70 Shore A

    ISO 868

    Operating Temperature

    -20 ℃ ~ +70 ℃

    —

    Tensile Strength

    ≥10 MPa

    ISO 37

    Weathering Test

    Test Item

    Test Condition

    Performance after Test

    UV-Aging Test

    QUV UV 340 lamp, 2000 hours

    No crack; Hardness change ≤5 ShoreA; Retain ≥80% tensile & elongationAlibaba.co...

    Ozone Aging

    50 pphm ozone, 40 ℃, 720 h

    No surface cracking

    Damp-Heat Aging

    85 ℃ / 85 % RH, 1000 h

    No blister, no delamination; compressionset remains acceptable

    Thermal Cycle

    -40 ℃ ↔ +85 ℃, 200 cycles

    No fracture, good resilience

    Application

    ● Used for crystalline silicon/amorphous silicon PV panels Applied in rooftop, ground-mounted & solar farm PV systems

    Advantages

    ● Prevents water intrusion, extends panel lifespan

    ● Reduces edge wear; maintains panel structural stability

    ● Easy to install, cuts maintenance costs

    Installation

    Step-by-Step Installation Guide
    1.Surface Preparation:
    Clean PV aluminum frame slots; remove dust, burrs and dirt; ensure dry surface.
    2.Cut to length:Cut PV-PE seal strip according to actual panel gap length, keep 0-2 mm margin.
    3.Insertion:Press multi-barb ribs of seal fully into the gap between adjacent PV frames; ensure locking barb fully seated inside the aluminum slot, do not leave partial hanging-out.
    4.Check compression:Recommended compression ratio: 20-30 %, guarantee waterproof sealing, avoid excessive squeezing leading to early fatigue failure.
    5.Joint handling:For long continuous runs, butt joints end-to-end neatly; small amount of neutral weather-resistant sealant can be applied at joints if required.

    R&D Centre - Laboratory


    R&D Centre - Laboratory

    Manufacturing Standards


    42b6d0cbefb10bf77cf24ccc69193199

    FAQ

    • 1. How do I select correct PV-PE model for my solar panels?

    • 2. What is difference between EPDM and PVC for PV-PE seal?

    • 3. Can you produce custom cross-section profile?

    • 4. What if the seal falls out after installation?

    • 5. Do you provide test reports?

    • 6. What is MOQ & lead-time?

    GET IN TOUCH

    Please fill in your question and we will reply you as soon as possible.

    AI Helps Write

    description2